Study on the machinability of resulfurized composite free-cutting steels

The machinability of S, S-Ca, S-RE, and S-RE-Ca system resulfurized composite free-cutting steels were investigated, where RE is rare earths, mostly cerium. The experimental results showed that in the low cutting speed range (≤35 m/min), the S-RE system free-cutting steel had better machinability than the others and that the S-RE-Ca system free-cutting steel exhibited the best machinability at high cutting speeds. A protective layer capable of preventing diffusion wear was formed on the rake face of a P30 tool when S-RE-Ca system free-cutting steel was machined in the cutting speed range of 120 to 160 m/min.     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.     

TPR处理剂的研究

利用活性单体苯乙烯与氯丁橡胶、高苯乙烯热塑弹性体接枝聚合，所得产物稀释后用于ＴＰＲ（ＴｈｅｒｍａｌＰｌａｓｔｉｃＲｕｂｂｅｒ）粘接前的预处理，可明显提高剥离强度。     

The deposition of coke from methane on a Ni/MgAl2O4 catalyst

Temperature-programmed reaction techniques and Raman spectroscopy were used to characterize coke species deposited on a 5% Ni/MgAl₂O₄ catalyst for dry reforming of methane. The CH₄ temperature-programmed decomposition profiles showed that the ignited decomposition temperatures of CH₄ increased from 273 to 378 °C when MgAl₂O₄ replaced the catalyst support γ-Al₂O₃. The temperature-programmed oxidation, temperature-programmed hydrogenation and temperature-programmed CO₂ reaction profiles showed that there were three carbon species (i.e. C_α, C_β and C_γ) on the catalyst surface. Raman spectroscopy showed that C_γ was graphite-like carbon species, which was responsible for catalyst deactivation. The C_γ species was the most inactive species toward H₂ and O₂, while it was unexpectedly more active toward CO₂. The unique reactivity of CO₂ with different coke specie could be ascribed to the carbonate, bidentate and formate species formation on MgAl₂O₄ surface. These surface species enhanced the oxidation of C_γ species and thus contributed to the high stability of Ni/MgAl₂O₄ catalyst.     

Crystal Chemistry and Phase Transitions in Substituted Pollucites along the CsAlSi2O6-CsTiSi2O6.5 Join: A Powder Synchrotron X-ray Diffractometry Study

The crystal structures for a suite of substituted pollucites with the compositions CsTi _x Al_{1– x} Si₂O_{6+0.5 x} , 0 ≤ x ≤ 1, have been determined from Rietveld analysis of powder synchrotron XRD data. Our results indicate that the pollucite end member (CsAlSi₂O₆) has a tetragonal structure (space group I 4₁/ a ), whereas all other compositions are cubic (space group Ia 3 d ). The increased symmetry for the titanium-substituted structures is presumably due to the incorporation of additional O²⁻ anions (needed for compensating the charge imbalance between Ti⁴⁺ and Al³⁺), which effectively holds open the expanded cubic framework. In situ cooling experiments of the substituted phase CsTi_0.1Al_0.9Si₂O_6.05 reveal a displacive transformation to the tetragonal structure at ∼230 K. This transformation is tricritical in nature and is analogous to the tetragonal-to-cubic transition in pollucite on heating.     

Braking Behavior of C/SiC Composites Prepared by Chemical Vapor Infiltration

Carbon fiber-reinforced silicon carbide matrix composites have the potential to overcome the shortcoming of the currently used carbon/carbon friction materials in aircraft brakes. In this article, the carbon/silicon carbide (C/SiC) composites were prepared by chemical vapor infiltration method, and the brake disks with different densities and component content were finally obtained. The friction coefficient and friction stability can be significantly improved by increasing both material density and carbon content. When the density of C/SiC composite is 2.3 g/cm³, the coefficient of friction measured is 0.23, the coefficient of friction stability remains about 0.43, the liner wear rate is less than 9.3 μm/cycle, and the weight wear rate is less than 9.1 μm/cycle. The rapid increase of friction coefficient approaching the end of braking is mainly related to the increasing of surface temperature in a short time and the enhanced adhesion and abrasion of contact conjunctions and asperities. The C/SiC composites exhibited a good stability of braking against fading versus the braking number and surface temperature. The surfaces of C/SiC brake disks were covered with wear debris including the fragment of carbon fibers after the braking tests. The wear on the surfaces is significantly determined by cyclic mechanical and thermal stresses, which result in the micro-cracks in the SiC matrix, the thin flakes of the surface materials as well as the grooves.     

HDPE／MPA层状容器加工及其阻透性能的研究

本文讨论了HDPE/MPA层状容器的加工以及MPA用量和贮存时间对阻透性的影响,分析了透过滞后、气相和液相透过现象。     

Grafting of alkoxyamine end-capped (co)polymers onto multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWNTs) have been successfully modified by polystyrene, poly(?-caprolactone), and their block copolymers by addition reaction of the alkoxyamine-terminated precursors. Polymer-modified MWNTs are easily dispersed in good solvents for the grafted polymer, such as toluene and THF. This observation has been confirmed by TEM analysis. The grafting ratio of polystyrene chains at the surface of MWNTs depends on the polymer molecular weight.     

氧化铁纳米棒的制备及其在光催化降解水溶性活性染料中的应用

采用均相沉淀法制备了半导体纳米材料α-Fe2O3.通过XRD、TEM等手段对该材料进行了分析.研究了烧结温度、光催化剂的用量、光照等因素对催化剂光催化降解活性染料的影响.并用红外和紫外的分析方法验证了光催化降解效果.结果表明,在适当的用量和350℃烧结并在紫外光照射下,α-Fe2O3对活性染料B-RN蓝、活性艳兰K-NR有极强的光催化降解活性.     

臭氧氧化法除地表水有机物试验研究

本文阐述臭氧化法除地表水有机物的重要意义，实验结果表明：臭氧氧化有机物的总氧化速率受活化控制，影响氧化率的最高显著因素是温度，其次是ｐＨ，接触时间等，臭氧很容易氧化腐植酸，在３０℃，ｐＨ９．０～１０．０，７ｍｉｎ内，ＣＯＤ去除率可达６０％以上，对邯郸热电厂生产处理也取得良好效果，３５℃，ｐＨ７．４～７．６，１０ｍｉｎ内，ＣＯＤ去除率可达６７％，可望将臭氧化水处理工艺应用于电厂水处理。